Ready-to-install rope starter for clockwise rotating Puch E50 engines on your Puch Maxi S / N or Puch Supermaxi LG1 moped / moped. Can only be fitted in conjunction with an MVT license plate.
Made in Switzerland. Designed for the highest loads and proven in racing.
Mounting:
- Starter pinion: Clean the MVT pole wheel, then screw the counterpart for the cable starter onto the pole wheel (secure the enclosed screws with Loctite).
- Pull starter: Position the starter housing in the correct position and tap lightly with a plastic hammer until the pull starter fits perfectly. It can then be screwed into place.
Application:
- Before starting, pull the cable slowly a few times so that the engine turns over empty (must be done before each start attempt).
- Pull out the cable starter handle until it engages fully and you encounter resistance. Then pull through in one go.
Tip: Wear gloves! Hold the handle firmly.
Note: The pedal mechanism can no longer be operated as the pedal arms would come into contact with the housing of the pull starter. Therefore, footrests, a longer pedal axle or a pedal axle extension must be fitted.
Further helpful parts for the cable starter conversion such as Loctite, racing gloves, replacement cord, rubber hammer etc. can be found in the accessories section. You can find them in the accessories section.
Exceptional product for the highest demands of the quality brand swiing®.
| Ø outside | 130 mm |
| Width | 150 mm |
| Manufacturer | swiing® ingenious parts |
| Material | Steel, Plastic |
| Surface | chrome-plated, raw |
| Color | Chrome, black-matt |
| Ignition system | MVT Allumage |
| Total length | 170 mm |
| Number of fixing points | 2 pcs |
| Hole spacing | 138 mm |
| Height | 82 mm |
| Puch | E50 |
Ratings
Accessories & related products
Loctite 243 medium-strength threadlocker 10 ml
Manufacturer: Loctite · Material to be used: Aluminum · Material to be used: Metal · Material to be used: Steel · Type of application: 1K · Color: blue · Contents: 10 ml · Area of application: Chemistry · Hazard warning: Causes serious eye irritation · Hazard warning: Causes skin irritation · Hazard warning: Harmful to aquatic organisms (with long-term effects) · Hazard warning: May cause allergic skin reactions · Hazard warning: May irritate the respiratory tract · Signal word: Attention · Hazard pictogram: GHS07 - Caution dangerous · Hazard pictogram: GHS09 - Hazardous to the aquatic environment · Adhesion: medium strength · Gap dimension (max.): 0.01 mm · Temperature resistance (min.): -75 - 200 °C · Alignment time: 600 sec · Breakaway torque (according to material): 3 N/m · Breakaway torque (according to material): 12 N/m · Breakaway torque (according to material): 26 N/m
25,00 EUR
2 500,00 EUR/l
GPO pedal axle with chrome rim | Puch Supermaxi LG1, LG2
Chain pitch: 1/2" x 3/16" · Total length: 257 mm · Manufacturer: GPO · Ø outside: 15.9 mm · Material: Steel · Color: Chrome · Number of teeth: 28 pcs · Surface: chrome-plated · Wavelength from wreath: 41 mm · Wavelength from wreath: 206 mm · Ø Outer sprocket: 120 mm · Ø Pedal arm holder: 15.9 mm · Ø Bearing support: 15.9 mm · Crank (wreath): 7.5 mm
68,50 EUR
MVT internal rotor ignition incl. rev limiter & light 12V | Puch / Sachs
Ø cable: 7 mm · Manufacturer: MVT Allumage · Manufacturer: swiing® ingenious parts · Tension: 12 V · Performance: 65 W · Direction of rotation: left · Ø mounting plate: 96 mm · Number of fixing points: 2 pcs · Ø Flywheel outside: 49.2 mm · Area of application: Tuning · Mounting type: Screws · Weight: 268 g
417,20 EUR
swiing® ingenious special screw M6x12 drive pinion pull rope starter MVT
Drive: Hexagon socket · Screw head: Countersunk head · Manufacturer: swiing® ingenious parts · Material: Steel · Surface: galvanized (blue) · Thread type: M6x1 (standard thread) · Width across flats: 4 mm · Total length: 12 mm
3,30 EUR
Moped fans also bought
GPO gasket set | Puch E50
Manufacturer: GPO · Material: Aluminum · Material: Fiber · Material: Sealing carton · Material: Sealing paper · Number of components: 7 pcs · Ø outlet inside: 19.9 mm · Area of application: Standard · Hole spacing outlet: 42 mm · Hole pattern [mm]: 44 x 44 · Decompressor: Yes · Hole spacing inlet: 32 - 38 mm
11,30 EUR
MBR clutch basket 18 teeth Racing straight | Puch E50
Manufacturer: MBR · Material: Steel · Toothing type: straight toothed · Ø Receptacle: 31 mm · Ø outside: 99.5 mm · Recording type: Interlocking · Ø inside: 15 mm · Ø inside: 17 mm · Height: 49 mm · Number of teeth: 18 pcs · Area of application: Tuning
211,40 EUR
MVT internal rotor ignition incl. rev limiter & light 12V | Puch / Sachs
Ø cable: 7 mm · Manufacturer: MVT Allumage · Manufacturer: swiing® ingenious parts · Tension: 12 V · Performance: 65 W · Direction of rotation: left · Ø mounting plate: 96 mm · Number of fixing points: 2 pcs · Ø Flywheel outside: 49.2 mm · Area of application: Tuning · Mounting type: Screws · Weight: 268 g
417,20 EUR
Collection only possible with online purchase and appointment.
