Intake manifold suitable for your Piaggio Ciao, Si or Bravo moped / moped for mounting a 16 / 16 SHA carburetor on the Speed Engine racing case.
With this inlet manifold, the Pinasco 16 / 16 SHA racing carburetor can be cleanly installed on the Polini Speed Engine racing case. The straight design creates a practical solution in the tight installation space and enables use in an inconspicuous variant. This allows you to exploit the potential of your carburetor without sacrificing a clean installation.
Notes:
The intake manifold already included with the Speed Engine racing case is angled. Depending on the Piaggio model, this may cause the carburetor to protrude from the frame and it may no longer be possible to fit an air filter.
The matching plastic bushing supplied with the 16 carburetor must be used for installation.
The matching racing carburetor and housing can be found in the accessories section.
A quality product manufactured in Switzerland.
| Camouflaged | No |
| Color | silver |
| Material | Aluminum |
| Thread type | M5x0.8 (standard thread) |
| Ø External connection | 19 mm |
| Ø inside | 16 mm |
| Number of fixing points | 2 pcs |
| Total length | 48.1 mm |
| Hole spacing inlet | 36 mm |
| Total height | 18.8 mm |
| Mounting type | Screws |
| Piaggio | Ciao - PX , C24 Si Bravo / Super Bravo Grillo |
Accessories & related products
Loctite 243 medium-strength threadlocker 10 ml
Temperature resistance (min.): -75 - 200 °C · Manufacturer: Loctite · Material to be used: Aluminum · Material to be used: Metal · Material to be used: Steel · Contents: 10 ml · Color: blue · Hazard warning: Causes serious eye irritation · Hazard warning: Causes skin irritation · Hazard warning: Harmful to aquatic organisms (with long-term effects) · Hazard warning: May cause allergic skin reactions · Hazard warning: May irritate the respiratory tract · Signal word: Attention · Hazard pictogram: GHS07 - Caution dangerous · Hazard pictogram: GHS09 - Hazardous to the aquatic environment · Area of application: Chemistry · Adhesion: medium strength · Gap dimension (max.): 0.01 mm · Type of application: 1K · Alignment time: 600 sec · Breakaway torque (according to material): 3 N/m · Breakaway torque (according to material): 12 N/m · Breakaway torque (according to material): 26 N/m
25,80 EUR
2 580,00 EUR/l
Polini Speed Engine engine housing electronic ignition | Piaggio Ciao, SI, Bravo, Boxer
Stock number: 6202 · Manufacturer: Polini · Material: Aluminum · Surface: sandblasted · Crankshaft stroke: 43 mm · Width: 175 mm · Color: silver · Ignition type: Electronic · Total length: 215 mm · Height: 104 mm
247,00 EUR
Polini Speed Engine engine case breaker ignition | Piaggio Ciao, SI, Bravo, Boxer
Stock number: 6202 · Manufacturer: Polini · Material: Aluminum · Surface: sandblasted · Crankshaft stroke: 43 mm · Total length: 215 mm · Color: silver · Ignition type: Breaker · Width: 175 mm · Height: 104 mm
247,00 EUR
Elring medium-strength threadlocker EL-Loc 43 blue 10 ml
Temperature resistance (min.): -55 - 180 °C · Manufacturer: Elring · Material to be used: Metal · Contents: 10 ml · Color: blue · Area of application: Chemistry · Adhesion: medium strength · Type of application: 1K · Alignment time: 300 sec · Breakaway torque (according to material): 15 N/m · Breakaway torque (according to material): 25 N/m
16,40 EUR
1 640,00 EUR/l
Pinasco 16/16 SHA carburetor hand choke | Piaggio Ciao PX / C24, Bravo, SUPERbravo
Manufacturer: Pinasco · Camouflaged: No · Area of application: Tuning · Component group Carburetor: Carburetor complete · Material: Aluminum · Color: silver · Carburetor type: SHA (Piaggio) · Total length: 45 mm · Nominal diameter: 16 mm · Width: 60 mm · Mounting type: Plug connection clamped · Height: 122 mm · Ø without reducing sleeve: 21 mm · Ø Internal connection: 16 mm · Ø Inside entrance: 16 mm · Ø Output inside: 16 mm · Ø Air filter connection: 50.5 mm · Ø fuel hose connection: 5.5 mm · Mixed oil connection: No · Vacuum connection: No · Choke control: Hand choke · Nozzle thread: M5x0.8 (standard thread) · Nozzle size: 79
117,50 EUR
Pinasco 16/16 SHA carburetor hand choke | Piaggio SI, Boss, Grillo
Manufacturer: Pinasco · Camouflaged: No · Area of application: Tuning · Component group Carburetor: Carburetor complete · Material: Aluminum · Color: silver · Carburetor type: SHA · Carburetor type: SHA (Piaggio) · Total length: 45 mm · Nominal diameter: 16 mm · Width: 60 mm · Mounting type: Plug connection clamped · Height: 122 mm · Ø without reducing sleeve: 21 mm · Ø Internal connection: 16 mm · Ø Inside entrance: 16 mm · Ø Output inside: 16 mm · Ø Air filter connection: 50.5 mm · Ø fuel hose connection: 5.5 mm · Mixed oil connection: No · Vacuum connection: No · Choke control: Hand choke · Nozzle thread: M5x0.8 (standard thread) · Nozzle size: 79
117,50 EUR
Explore categories from Carburetor & intake system
Attention: new opening hours from 16.02.2026 & new evening sale on Thursday 17:30-20:00
