SpeedEngine racing case from Polini for your Piaggio Ciao, Si, Bravo and Boxer moped / moped.
This version of the engine case is designed for electronic ignition and cannot be used for contact ignition.
The engine housing impresses with its clean finish and is perfect for cylinder kits with a piston diameter of up to 46 mm.
Ideally, you should use a Polini cylinder. However, the overflow ports of the Malossi cylinder kits (from 2021) or those of the DR 43 mm racing kit also fit quite well.
The intake manifold is designed for Dell'Orto SHA type 3 carburettors with up to 13 mm passage.
The intake timing is already very long ex works. Therefore, the engine block can also be operated with the original crankshaft.
If you want to get even more power, we recommend using a racing crankshaft.
With the optionally available swiing intake manifold, it is also possible to operate larger carburetors than a 13/13.
Matching parts such as racing cylinders, racing shafts or our swiing intake manifolds with matching carburetors can be found in the accessories section.
Quality product from the Italian manufacturer Polini.
| Stock number | 6202 |
| Manufacturer | Polini |
| Material | Aluminum |
| Color | silver |
| Surface | sandblasted |
| Crankshaft stroke | 43 mm |
| Total length | 215 mm |
| Width | 175 mm |
| Height | 104 mm |
| Ignition type | Electronic |
| Piaggio | Ciao - P , SC , PX , C24 Si Bravo / Super Bravo Boxer Grillo |
Ratings
Accessories & related products
Dell'Orto 16/16 SHA carburetor hand choke
Nominal diameter: 16 mm · Manufacturer: Dell'Orto · Material: Aluminum · Component group Carburetor: Carburetor complete · Color: black · Carburetor type: SHA · Total length: 82 mm · Width: 72 mm · Ø fuel hose connection: 5.1 mm · Ø fuel hose connection: 6 mm · Height: 111 mm · Ø without reducing sleeve: 21 mm · Ø Inside entrance: 16 mm · Ø Internal connection: 19 mm · Mounting type: Plug connection clamped · Ø Output inside: 16 mm · Ø Air filter connection: 56 mm · Ø Air filter connection: 58.5 mm · Mixed oil connection: No · Vacuum connection: No · Choke control: Hand choke · Nozzle thread: M5x0.8 (standard thread) · Camouflaged: No · Nozzle size: 82 · Area of application: Tuning
82,30 EUR
GPO 19.5 mm PHBG AD carburetor cable choke (Dell'Orto replica)
Nominal diameter: 19.5 mm · Width: 75 mm · Manufacturer: GPO · Area of application: Tuning · Component group Carburetor: Carburetor complete · Carburetor type: PHBG AD · Height: 130 mm · Ø without reducing sleeve: 26 mm · Ø Internal connection: 24 mm · Mounting type: Plug connection clamped · Ø Air filter connection: 32 mm · Air filter connection thread: MF32x1.25 (fine pitch thread) · Ø fuel hose connection: 6 mm · Mixed oil connection: Yes · Choke control: Cable choke · Choke nozzle size: 55 · Nozzle thread: M5x0.8 (standard thread) · Nozzle size: 85 · Size of secondary nozzle: 50
94,00 EUR
Polini Racing 43 mm cylinder kit incl. head 10 mm KoBo | Piaggio Ciao, Bravo, Boxer
Nominal diameter: 43 mm · Manufacturer: Polini · Material: Gray cast iron · Surface: sandblasted · Displacement: 63 ccm · Crankshaft stroke: 43 mm · Ø cylinder neck: 45.7 mm · Ø Outlet outside: 22.4 mm · Ø outlet inside: 18.1 mm · Ø piston pin (B): 10 mm · Outlet type: clamped · Number of fixing points: 3 pcs · Hole pattern [mm]: 55 x 34 · Decompressor: Yes · Camouflaged: No · Area of application: Tuning
282,30 EUR
Polini 46 mm cylinder kit incl. head 10 mm KoBo | Piaggio Ciao, Bravo, Boxer
Nominal diameter: 46 mm · Manufacturer: Polini · Material: Gray cast iron · Surface: sandblasted · Displacement: 70 ccm · Crankshaft stroke: 43 mm · Ø piston pin (B): 10 mm · Outlet type: clamped · Number of fixing points: 3 pcs · Decompressor: Yes · Camouflaged: No · Area of application: Tuning
282,30 EUR
Polini 43 mm cylinder kit incl. head 10 mm KoBo | Piaggio Ciao, Bravo, Boxer
Nominal diameter: 43 mm · Manufacturer: Polini · Material: Gray cast iron · Surface: sandblasted · Displacement: 63 ccm · Crankshaft stroke: 43 mm · Ø piston pin (B): 10 mm · Outlet type: clamped · Number of fixing points: 3 pcs · Decompressor: Yes · Camouflaged: No · Area of application: Tuning
264,60 EUR
Mazzucchelli crankshaft "Racing" 10 mm KoBo | Piaggio Ciao, SI, Bravo, Boxer
Manufacturer: Mazzucchelli · Area of application: Racing · Material: Steel · Cheek type: standard · Ø coupling pin / vario pin: 12 mm · Crankshaft stroke: 43 mm · Ø piston pin (B): 10 mm · Thread type: M8x1.25 (standard thread) · Connecting rod length center-center: 87 mm · Thread length: 16 mm · Weight: 698 g · Total length crankpin ignition side: 90 mm · Total length crankpin ignition side: 106 mm · Ø crank webs: 69.7 mm · Ø Connecting rod eye: 13 mm · Bearing seat right: 15 mm · Ø Bearing seat (ignition side): 15 mm · Dimension needle bearing: 10 / 13 x 14.2 mm (axe 10) · Wide crank webs: 33 mm · Length 1st paragraph: 21 mm · Length 2nd paragraph: 44 mm · Length 3rd paragraph: 63.5 mm · Ø 1st step (on the coupling side): 15 mm · Ø 2nd shoulder (on the clutch side): 14.4 mm · Ø 3rd step (on the clutch side): 12 mm · Inlet control time: 139 ° · Control time before O.T: 81 ° · Control time according to O.T: 58 ° · Number of gears: 1 pcs
176,40 EUR
swiing® ingenious 16 mm SHA intake manifold Speed Engine | Piaggio Ciao, SI, Bravo
Manufacturer: swiing® ingenious parts · Camouflaged: No · Area of application: Tuning · Color: graphite colors · Material: Aluminum · Surface: anodized · Ø inside: 16 mm · Ø External connection: 19 mm · Hole spacing inlet: 36 mm · Mounting type: Screws · Number of fixing points: 2 pcs · Total height: 24.2 mm · Total length: 29 mm
38,70 EUR
swiing® ingenious 19 mm PHBG intake manifold Speed Engine | Piaggio Ciao, SI, Bravo
Manufacturer: swiing® ingenious parts · Material: Aluminum · Surface: anodized · Color: graphite colors · Ø inside: 19 mm · Mounting type: Screws · Ø External connection: 24 mm · Hole spacing inlet: 36 mm · Number of fixing points: 2 pcs · Area of application: Tuning
35,20 EUR
Dell'Orto 13/13 SHA carburetor & racing air filter set | Piaggio Ciao PX, C24
Manufacturer: Dell'Orto · Manufacturer: Malossi · Area of application: Tuning · Component group Carburetor: Carburetor complete · Width: 60 mm · Choke control: Hand choke · Carburetor type: SHA (Piaggio) · Height: 96 mm · Nominal diameter: 13 mm · Total length: 46 mm · Ø fuel hose connection: 6 mm · Ø without reducing sleeve: 18 mm · Ø Inside entrance: 13 mm · Ø Internal connection: 16 mm · Ø Output inside: 13 mm · Ø Air filter connection: 50.8 mm · Mounting type: Plug connection clamped · Nozzle thread: M5x0.8 (standard thread) · Nozzle size: 66
78,70 EUR
GPO stator electronic ignition with light (one output) | Piaggio Ciao, SI, Bravo, Boxer
Manufacturer: GPO · Tension: 12 V · Performance: 90 W · Number of cables: 4 pcs · Cable length: 100 mm · Cable length: 400 mm · Ø outside: 105 mm · Number of fixing points: 3 pcs · Hole spacing: 34.5 mm
117,50 EUR
swiing® ingenious 6202 Bearing dummy 15/35/11 Aluminum
Bearing type: Deep groove ball bearing · Stock number: 6202 · Ø inside: 15 mm · Ø outside: 35 mm · Width: 12 mm · Manufacturer: swiing® ingenious parts · Material: Aluminum · Area of application: Special tool · Area of application: Workshop accessories · Surface: anodized
11,70 EUR
Explore categories from Gearbox & housing (motor)
Moped fans also bought
SKF 6202 C3 ball bearing 15/35/11
Bearing type: Deep groove ball bearing · Stock number: 6202 · Inner ring width: 11 mm · Manufacturer: SKF · Bearing clearance: C3 · Bearing cage: Sheet steel cage ball-guided · Width: 11 mm · Ø inside: 15 mm · Ø outside: 35 mm · Puch OEM number: 900.4.6202
11,70 EUR
swiing® revival stud bolt set M7x120 mm cylinder | Piaggio Ciao, SI, Bravo, Boxer
Manufacturer: swiing® revival parts · Material: Steel · Surface: galvanized (blue) · Diameter: 6.2 mm · Thread type: M7x1 (standard thread) · Drive: External hexagon · Thread length: 25 mm · Total length: 120 mm · Width across flats: 11 mm · Strength class: 8 · Strength class: 8.8
13,80 EUR
swiing® revival screw set galvanized fan cover | Piaggio Ciao, SI, Bravo, Boxer
Manufacturer: swiing® revival parts · Area of application: Standard · Material: Steel · Surface: galvanized (blue) · Thread type: M5x0.8 (standard thread) · Drive: Cross recess · Screw head: Panhead · Number of components: 8 pcs
5,75 EUR
swiing® revival screw set stator galvanized | Piaggio Ciao, SI, Bravo, Boxer
Manufacturer: swiing® revival parts · Area of application: Standard · Material: Steel · Surface: galvanized (blue) · Drive: Cross recess · Screw head: Lens head · Thread type: M5x0.8 (standard thread) · Thread length: 20 mm · Shank: No · Number of components: 6 pcs
4,60 EUR
GPO stator electronic ignition with light (one output) | Piaggio Ciao, SI, Bravo, Boxer
Manufacturer: GPO · Tension: 12 V · Performance: 90 W · Number of cables: 4 pcs · Cable length: 100 mm · Cable length: 400 mm · Ø outside: 105 mm · Number of fixing points: 3 pcs · Hole spacing: 34.5 mm
117,50 EUR
GPO flywheel 800 g rotary valve shaft electronic ignition | Piaggio Ciao, SI, Bravo, Boxer
Manufacturer: GPO · Material: Aluminum · Direction of rotation: right · Weight: 800 g · Thread type: MF17x1 (fine pitch thread) · Ø Internal flywheel: 106 mm · Ø Flywheel outside: 139.5 mm · Piaggio OEM number: 181103 · Piaggio OEM number: 2238183
188,20 EUR
Attention: new opening hours from 16.02.2026 & new evening sale on Thursday 17:30-20:00
