Socket axle set with closed groove ball bearings (Ø 29 mm) for front cast hubs (Leleu) on your Puch moped / moped.
The threaded shaft set consists of a 165 mm long wheel axle, two special ball bearings and all required nuts and spacers.
The wheel axle set works with Leleu front wheel hubs, which are installed in cast rims.
The cable ties show you where to fit what:
- Red cable tie: wheel hub
- green cable tie: brake anchor plate
- Yellow cable tie: Replacement disk for the speedometer drive (the disk is removed if a drive is fitted)
- Blue cable ties: fork braces
Note: When mounting the ball bearings, it is important to note that the long spacer bush between the two ball bearings must be clamped to ensure that the two bearings press with the inner ring on the bushing. If this is not observed, the ball bearings will inevitably jam.
| Ø inside | 12 mm |
| Ø outside | 29.02 mm |
| Width | 34.5 mm, 6.6 mm, 11 mm, 2.7 mm |
| Manufacturer | swiing® ingenious parts |
| Ball bearing closed | Yes |
| Material | Steel |
| Surface | galvanized (blue) |
| Height | 9.9 mm, 5.9 mm |
| Total length | 165 mm |
| Width across flats | 19 mm |
| Ø shaft | 11.95 mm |
| Shank length | 74.5 mm |
| Thread length | 50 mm, 40.5 mm |
| Thread type | MF12x1 (fine pitch thread) |
| Puch |
Accessories & related products
Hot 
swiing® ingenious wheel axle with bearing conversion kit spoke hub front | Puch
Ø inside: 12 mm · Ø outside: 29.02 mm · Total length: 165 mm · Ball bearing closed: Yes · Manufacturer: swiing® ingenious parts · Material: Steel · Surface: galvanized (blue) · Width: 2.7 mm · Width: 6.6 mm · Width: 11 mm · Width: 35.7 mm · Height: 5.9 mm · Height: 9.9 mm · Ø shaft: 11.95 mm · Shank length: 74.5 mm · Thread type: MF12x1 (fine pitch thread) · Width across flats: 19 mm · Thread length: 40.5 mm · Thread length: 50 mm
45,80 EUR
Hot
swiing® ingenious wheel axle with bearing conversion kit rear spoke hub | Puch
Ø inside: 12 mm · Ø outside: 29 mm · Total length: 190 mm · Ball bearing closed: Yes · Manufacturer: swiing® ingenious parts · Material: Steel · Surface: galvanized (blue) · Diameter: 29 mm · Ø shaft: 19 mm · Shank length: 100 mm · Thread type: MF12x1 (fine pitch thread) · Width across flats: 19 mm · Thread length: 29 mm · Thread length: 53 mm
45,80 EUR
swiing® ingenious wheel bearing 12/29/9 spoke & cast rim | Puch Maxi
Bearing type: Deep groove ball bearing · Ø inside: 12 mm · Ø outside: 29.02 mm · Inner ring width: 9 mm · Ball bearing closed: Yes · Manufacturer: swiing® ingenious parts · Dust protection type: 2RS - NBR contact seal on both sides · Bearing clearance: CN (standard) · Bearing cage: Sheet steel cage ball-guided · Material: Plastic · Material: Steel · Width: 9 mm
10,50 EUR
GPO speedo drive 17" with lugs 12 mm axle | Puch Maxi S / N, X30 Sport NS / NL, NG-2AH, X30 Velux
Manufacturer: GPO · Material: Aluminum · Thread type: MF10x1 (fine pitch thread) · 4-edge speedometer cable: 1.8 mm · 4-edge speedometer cable: 2.6 mm · Ø axle: 12 mm · Place of use: left · Place of use: right · Total height: 10 mm · Ø mounting hole: 12 mm · Wheel size: 17 " · Ø outside: 41 mm
32,80 EUR
Explore categories from Hub & axle
Moped fans also bought
NTN wheel bearing 12/28/8 rear cast hub Leleu | Puch Maxi
Bearing type: Deep groove ball bearing · Ø inside: 12 mm · Ø outside: 28 mm · Inner ring width: 12 mm · Manufacturer: NTN · Ball bearing closed: Yes · Dust protection type: 2RS - NBR contact seal on both sides · Bearing clearance: CM (special/noise-reduced) · Bearing cage: Sheet steel cage ball-guided · Groove ring: No · Material: Plastic · Material: Steel · Stock number: 6001 · Width: 8 mm · Area of application: Standard
6,95 EUR
swiing® revival wheel axle LELEU & Grimeca wheel hub cast wheel rear | Puch
Ø outside: 11.8 mm · Total length: 185 mm · Manufacturer: swiing® revival parts · Material: Steel · Surface: galvanized (blue) · Ø shaft: 11.9 mm · Shank length: 100 mm · Thread type: MF12x1 (fine pitch thread) · Width across flats: 19 mm · Thread length: 26 mm · Thread length: 52.5 mm
17,50 EUR
Hot
swiing® ingenious wheel axle with bearing conversion kit rear spoke hub | Puch
Ø inside: 12 mm · Ø outside: 29 mm · Total length: 190 mm · Ball bearing closed: Yes · Manufacturer: swiing® ingenious parts · Material: Steel · Surface: galvanized (blue) · Diameter: 29 mm · Ø shaft: 19 mm · Shank length: 100 mm · Thread type: MF12x1 (fine pitch thread) · Width across flats: 19 mm · Thread length: 29 mm · Thread length: 53 mm
45,80 EUR
Hot
Inner cable set automatic | Puch E50
Total length: 1600 mm · Total length: 2200 mm · Manufacturer: Made in Germany · Material: Steel · Quantity: 4 pcs · Ø Stranded wire: 1.25 mm · Ø Stranded wire: 1.5 mm · Ø Stranded wire: 1.8 mm · Nipple shape: Barrel (transverse) · Nipple shape: Cylinder · Nipple shape: Pears
11,70 EUR
swiing® revival wheel axle set LELEU wheel hub cast wheel rear | Puch
Ø inside: 12 mm · Ø outside: 28 mm · Ø outside: 29 mm · Total length: 190 mm · Manufacturer: SKF · Ball bearing closed: Yes · Manufacturer: swiing® revival parts · Material: Steel · Surface: galvanized (blue) · Width: 8 mm · Width: 9 mm
36,40 EUR
SKF 6001 2RSH Ball bearing 12/28/8
Bearing type: Deep groove ball bearing · Ø inside: 12 mm · Ø outside: 28 mm · Inner ring width: 8 mm · Manufacturer: SKF · Ball bearing closed: Yes · Dust protection type: 2RSH - NBR contact seal on both sides · Bearing clearance: CN (standard) · Bearing cage: Sheet steel cage ball-guided · Stock number: 6001 · Width: 8 mm
15,20 EUR
Attention: new opening hours from 16.02.2026 & new evening sale on Thursday 17:30-20:00
