Replica wire spoke hub made of aluminum with pressed-in bearings for the rear wheel of various mopeds, mopeds and small motorcycles.
Note: The hub is at the limit of tolerances in the area of the brake drum and sprocket mount. The function is just about guaranteed, but you shouldn't expect too much.
The bearings installed are also not of particularly high quality.
You can find suitable add-on parts for the rear hub such as brake pads, clamping screws etc. in the accessories section.
| Ø inside | 30 mm |
| Material | Aluminum |
| Surface | blank |
| Ø axle | 12 mm |
| Ø Receptacle | 93 mm |
| Ø drum | 80 mm |
| Area of application | Standard, Custom |
| Number of spoke holes | 36 pcs |
| Puch |
Accessories & related products
Brake cable Ø 1.8 mm x 220 cm (pear-shaped nipple)
Ø Stranded wire: 1.8 mm · Nipple shape: Pears · Ø nipple: 3.5 mm · Ø nipple: 6 mm · Manufacturer: Made in Germany · Area of application: Standard · Material: Steel · Surface: galvanized (blue) · Number of components: 1 pcs · Cable length: 2200 mm · Nipple length: 10 mm
2,80 EUR
swiing® revival wheel axle set LELEU wheel hub cast wheel rear | Puch
Width: 8 mm · Width: 9 mm · Ø inside: 12 mm · Ø outside: 28 mm · Ø outside: 29 mm · Manufacturer: SKF · Manufacturer: swiing® revival parts · Material: Steel · Surface: galvanized (blue) · Total length: 190 mm · Ball bearing closed: Yes
36,20 EUR
swiing® revival rear brake anchor plate | Puch Maxi S, X30 NG
Ø outside: 91 mm · Manufacturer: swiing® revival parts · Material: Steel · Surface: galvanized (blue) · Ø axle: 12 mm · Ø External brake pads: 80 mm · Ø shaft: 10 mm · Wide cam holder: 12 mm · Cranking (offset): 8 mm · Brake lever length (lever length): 55 mm · Ø bore: 12.2 mm · Total length: 187 mm · Ø screw holder: 6.5 mm
81,90 EUR
swiing® revival rear brake anchor plate | Puch Maxi N
Ø outside: 92 mm · Manufacturer: swiing® revival parts · Material: Steel · Surface: galvanized (blue) · Ø axle: 12 mm · Ø External brake pads: 80 mm · Ø shaft: 10 mm · Wide cam holder: 12 mm · Cranking (offset): 10 mm · Brake lever length (lever length): 68 mm · Ø bore: 12.2 mm · Total length: 135 mm · Ø screw holder: 6.5 mm
87,80 EUR
Magura set screw M6x34 mm lock nut SW10
Slotted: No · Width across flats Screw: 8 mm · Manufacturer: Magura · Width across flats nut: 10 mm · Thread type: M6x1 (standard thread) · Material: Brass · Surface: nickel-plated · Ø cable holder: 3.05 mm · Ø Receptacle: 7.05 mm · Total length: 34 mm · Thread length: 23 mm
2,95 EUR
swiing® revival wheel axle M12x1 x 185 rear (closed ball bearing) | Puch
Manufacturer: swiing® revival parts · Thread type: MF12x1 (fine pitch thread) · Material: Steel · Surface: galvanized (blue) · Width across flats SW: 7 mm · Ø shaft: 11.95 mm · Shank length: 99 mm · Total length: 185 mm · Thread length: 28 mm · Thread length: 52 mm
11,60 EUR
SKF 16101 2RS1 ball bearing 12/30/8
Width: 8 mm · Bearing cage: "-" Sheet steel cage ball-guided · Ø inside: 12 mm · Ø outside: 30 mm · Stock number: 16101 · Inner ring width: 8 mm · Manufacturer: SKF · Dust protection type: 2RS1 - NBR contact seal on both sides · Bearing clearance: CN (standard) · Groove ring: No · Material: Plastic · Area of application: Standard · Material: Steel · Surface: blank · Bearing type: Deep groove ball bearing · Ball bearing closed: Yes
19,10 EUR
Moped fans also bought
GPO 38 mm cylinder head original | Puch Maxi S, N / X30 NS, NL, N-2AH
Height: 55 mm · Width: 125 mm · Manufacturer: GPO · Material: Aluminum · Area of application: Standard · Surface: sandblasted · Ø cylinder: 38 mm · Number of fixing points: 4 pcs · Candle thread: short · Total length: 135 mm · Hole pattern [mm]: 44 x 44 · Decompressor: No
38,60 EUR
GPO 17" spoke set incl. nipple (2.9 x 188 mm) Inox
Manufacturer: GPO · Material: Chrome steel (known as Nirosta®) · Quantity: 36 pcs · Surface: raw · Color: silver · Length from hook: 188 mm · Ø spoke: 2.9 mm · Ø spoke head: 5.35 mm · Nominal diameter (thread): 3.15 mm · Nipple length: 14 mm · Ø nipple head: 7.9 mm · Ø Nipple neck: 5 mm · Hook length: 9 mm · Thread length: 11 mm · Hook angle: 95 °
64,30 EUR
swiing® ingenious wheel axle with bearing conversion kit spoke hub front Ø 29 mm | Puch
Width: 2.7 mm · Height: 5.9 mm · Width: 6.6 mm · Height: 9.9 mm · Width: 11 mm · Width: 35.7 mm · Ø inside: 12 mm · Ø outside: 29.02 mm · Manufacturer: swiing® ingenious parts · Thread type: MF12x1 (fine pitch thread) · Material: Steel · Surface: galvanized (blue) · Width across flats SW: 19 mm · Ø shaft: 11.95 mm · Shank length: 74.5 mm · Total length: 165 mm · Ball bearing closed: Yes · Thread length: 40.5 mm · Thread length: 50 mm
45,60 EUR
swiing® revival rear brake anchor plate | Puch Maxi S, X30 NG
Ø outside: 91 mm · Manufacturer: swiing® revival parts · Material: Steel · Surface: galvanized (blue) · Ø axle: 12 mm · Ø External brake pads: 80 mm · Ø shaft: 10 mm · Wide cam holder: 12 mm · Cranking (offset): 8 mm · Brake lever length (lever length): 55 mm · Ø bore: 12.2 mm · Total length: 187 mm · Ø screw holder: 6.5 mm
81,90 EUR
Collection only possible with online purchase and appointment.
