Racing clutch for all E50 input automatic engines, which are installed on Puch Maxi S / N mopeds / mopeds, among others.
The 3-jaw centrifugal clutch has lightweight aluminum linings. As a result, the engagement point is higher than with original clutch linings.
In addition, the wear of the friction linings is significantly lower due to the lower weight.
Please select the desired clutch springs in the selection field.
Note: Due to the later engagement point, this clutch cannot be used with an original, sealed cylinder.
The clutch is suitable for cylinder kits up to 44 mm in combination with the original or reinforced blue clutch springs. If you use larger cylinders or install even stiffer springs, wear will be increased and the clutch will wear out quickly.
Good, inexpensive standard spare part. GPO – GOOD PARTS ONLY.
Manufacturer: GPO · Material: Steel · Material addition: Aluminum, Steel · Recording type: Cone mounting · Number of jaws: 3 pcs · Number of springs: 3 pcs · Ø outside: 93.5 mm · Thickness: 21 mm · Area of application: Standard, Original, Performance, Tuning
| Manufacturer | GPO |
| Material | Aluminum, Steel |
| Recording type | Cone mounting |
| Number of jaws | 3 pcs |
| Number of springs | 3 pcs |
| Thickness | 21 mm |
| Ø outside | 93.5 mm |
| Area of application | Tuning |
| Puch | E50 |
Accessories & related products
swiing® ingenious clutch springs reinforced (+20%) | Puch E50
Spring design: Pressure spring · Ø wire: 1.7 mm · Manufacturer: swiing® ingenious parts · Material: Spring steel · Area of application: Tuning · Surface: coated · Color: blue · Number of components: 3 pcs · Ø outside: 8.3 mm · Ø inside: 4.8 mm · Total length: 28 mm
21,00 EUR
HK clutch "Racing" Aramid | Puch E50
Material: Steel · Manufacturer: HK Clutches · Material addition: Chrome steel (known as Nirosta®) · Recording type: Cone mounting · Number of jaws: 3 pcs · Area of application: High End · Area of application: Performance · Area of application: Racing · Area of application: Tuning · Number of springs: 3 pcs
351,60 EUR
Not in stock
swiing® revival gearbox cover gasket 0.3 mm engine | Puch E50
Manufacturer: swiing® revival parts · Material: Sealing paper · Color: sand-colored · Thickness: 0.35 mm · Ø outside: 116 mm · Ø inside: 106 mm · Number of fixing points: 4 pcs · Number of components: 1 pcs · Puch OEM number: 349.1.10.349.1
2,80 EUR
swiing® revival gasket gearbox cover engine 0.5 mm | Puch E50
Manufacturer: swiing® revival parts · Thickness: 0.5 mm · Material: Sealing paper · Color: sand-colored · Number of components: 1 pcs · Ø outside: 116 mm · Ø inside: 106 mm · Number of fixing points: 4 pcs · Alternative version of the Puch OEM number: 349.1.10.349.1
3,40 EUR
Moped fans also bought
swiing® ingenious clutch springs reinforced (+20%) | Puch E50
Spring design: Pressure spring · Ø wire: 1.7 mm · Manufacturer: swiing® ingenious parts · Material: Spring steel · Area of application: Tuning · Surface: coated · Color: blue · Number of components: 3 pcs · Ø outside: 8.3 mm · Ø inside: 4.8 mm · Total length: 28 mm
21,00 EUR
Hot 
swiing® ingenious 15 mm carburetor tuning camouflaged | Puch
Nominal diameter: 15 mm · Manufacturer: swiing® ingenious parts · Material: Aluminum · Area of application: Tuning · Camouflaged: Yes · Component group Carburetor: Carburetor complete · Carburetor type: SRE · Ø Internal connection: 20 mm · Total length: 66 mm · Ø Inside entrance: 15 mm · Ø Output inside: 15 mm · Ø Air filter connection: 20 mm · Width: 50 mm · Height: 95 mm · Ø fuel hose connection: 6 mm · Mixed oil connection: No · Vacuum connection: No · Choke control: Hand choke · Nozzle thread: M3.5x0.6 (standard thread) · Nozzle block: 2.17 · Nozzle size: 62 · Mounting type: Plug connection clamped · Clamping screw torque (max.): 4 N/m
93,70 EUR
swiing® revival gasket gearbox cover engine 0.5 mm | Puch E50
Manufacturer: swiing® revival parts · Thickness: 0.5 mm · Material: Sealing paper · Color: sand-colored · Number of components: 1 pcs · Ø outside: 116 mm · Ø inside: 106 mm · Number of fixing points: 4 pcs · Alternative version of the Puch OEM number: 349.1.10.349.1
3,40 EUR
swiing® revival gasket gearbox cover engine 1 mm | Puch E50
Manufacturer: swiing® revival parts · Thickness: 1 mm · Material: Sealing paper · Color: sand-colored · Number of components: 1 pcs · Ø outside: 116 mm · Ø inside: 106 mm · Number of fixing points: 4 pcs · Alternative version of the Puch OEM number: 349.1.10.349.1
4,55 EUR
swiing® ingenious crankshaft High End with mounted bearings | Puch E50
Manufacturer: swiing® ingenious parts · Weight: 968 g · Material: Aluminum · Material: Steel · Cheek type: Full cheeks · Crankshaft stroke: 43 mm · Connecting rod length center-center: 90 mm · Total length of crankpin on clutch side: 74 mm · Total length crankpin ignition side: 66 mm · Ø crank webs: 69.9 mm · Ø piston pin (B): 12 mm · Ø Connecting rod eye: 15 mm · Area of application: High End · Area of application: Racing · Area of application: Tuning · Ø Bearing seat (clutch side): 17 mm · Ø Bearing seat (ignition side): 17 mm · Thread type: MF10x1 (fine pitch thread) · Thread length: 11 mm · Dimension needle bearing: 12 / 15 x 14.2 mm (axe 12) · Thread length: 15 mm · Wide crank webs: 34 mm · Length 1st paragraph: 9 mm · Length 2nd paragraph: 14.5 mm · Length 3rd paragraph: 25 mm · Ø 1st step (on the coupling side): 22 mm · Ø 2nd shoulder (on the clutch side): 17 mm · Ø 3rd step (on the clutch side): 15 mm · Length of shoulder (ignition side): 26.3 mm · Number of gears: 1 pcs
210,90 EUR
Collection only possible with online purchase and appointment.
